2024年1月11日发(作者：宝豫)

华为MA5680T配置

MA5620E基本配置:

MA5620E>

MA5620E>enable

MA5620E#config

MA5620E(config)#

MA5620E(config)#sysname Epon-xiangjiang-2qi-dong-1-1 ------------------/给设备起名字/

xiangjiang-2qi-dong-1-1(config)#vlan 100 ------------------------------/建onu的管理vlan/

xiangjiang-2qi-dong-1-1(config)#vlan 200 --------------------------------/建楼宇的管理vlan/

xiangjiang-2qi-dong-1-1(config)#vlan 3001 to 3016 -----------------------/这个onu所用pppoe vlan/

xiangjiang-2qi-dong-1-1(config)#port vlan 100 0/0 1 ------------------- /允许上行vlan/

xiangjiang-2qi-dong-1-1(config)#port vlan 200 0/0 1 ------------------- /允许上行vlan/

xiangjiang-2qi-dong-1-1(config)#port vlan 3001 to 3016 0/0 1 ------------- /允许pppoe vlan/

注意:onu自己用的vlan在上联口上透传 ，楼宇交换机用的vlan不用做透传

xiangjiang-2qi-dong-1-1(config)#int vlan 100 ----------------------------- /进入vlan/

xiangjiang-2qi-dong-1-1 (config-if-vlanif100)#ip add 10.247.32.2 26

------- /建onu的管理ip/

xiangjiang-2qi-dong-1-1 (config-if-vlanif100)#quit 退一级

xiangjiang-2qi-dong-1-1(config)# ip route 0.0.0.0 0.0.0.0

10.247.32.1 ------ /

缺省路由/

二、建用户pvc于拨号和透传

xiangjiang-2qi-dong-1-1(config)# undo service-port all --------------------- / 先

删除原有的pvc

前13个eth口用于pppoe，14、15、16三个口用于级联楼宇交换机

xiangjiang-2qi-dong-1-1(config)#

service-port vlan 3001 eth 0/1/1 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3002 eth 0/1/2 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3003 eth 0/1/3 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3004 eth 0/1/4 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3005 eth 0/1/5 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3006 eth 0/1/6 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3007 eth 0/1/7 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3008 eth 0/1/8 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3009 eth 0/1/9 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3010 eth 0/1/10 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3011 eth 0/1/11 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3012 eth 0/1/12 user-vlan untagged rx-cttr 6 tx-cttr 6

service-port vlan 3013 eth 0/1/13 user-vlan untagged rx-cttr 6 tx-cttr 6

透传口

(config)#service-port vlan transparent eth 0/1/14 other-all rx-cttr

6 tx-cttr 6

(config)#service-port vlan transparent eth 0/1/15 other-all rx-cttr

6 tx-cttr 6

(config)#service-port vlan transparent eth 0/1/16 other-all rx-cttr

6 tx-cttr 6

最后保存退出

xiangjiang-2qi-dong-1-1(config)#save

xiangjiang-2qi-dong-1-1(config)#quit

EPON配置针对MA5620E的业务数据:

MA5680T(config)#vlan 1002 to 1003 smart

//配置业务VLAN=1002 to 1003

MA5680T(config)#port vlan 1002 to 1003 0/20 0

//从上行口0/20/0透传业务VLAN

MA5680T(config)#service-port vlan 1002

{ adsl|shdsl|vdsl|atm|eth|gpon|epon }:epon

{ frameid/slotid/portid<1,15> }:0/15/0

{ ont }:ont

{ ontid<0,63> }:1

{ |multi-service }:multi-service

{ user-vlan }:user-vlan

{ user-vlanid<1,4094>|untagged }:1002

MA5680T(config)#service-port vlan 1003

{ adsl|shdsl|vdsl|atm|eth|gpon|epon }:epon

{ frameid/slotid/portid<1,15> }:0/15/0

{ ont }:ont

{ ontid<0,63> }:1

{ |multi-service }:multi-service

{ user-vlan }:user-vlan

{ user-vlanid<1,4094>|untagged }:1003

//配置2条业务流

下面的数据就需要telnet登录MA5620E上进行配置

MA5680T(config)#telnet 192.168.100.2

{ |service-port<0,4294967295> }:

Command:

telnet 192.168.100.2

Press CTRL_] to quit telnet mode

Trying 192.168.100.2 ...

Connected to 192.168.100.2 ...

>>User name:root

>>User password:mduadmin

Huawei Integrated Access Software.

Copyright(C) Huawei Technologies Co., Ltd. 1998-2008. All rights

reserved.

MA5620E>enable

MA5620E#config

MA5620E(config)# vlan 1002 to 1003 ----------------------- //创建业务VLAN

MA5620E(config)#port vlan 1002 to 1003 0/0 1 --------------//从上行口透传业务VLAN

MA5620E(config)#undo service-port all ------------------ //删除默认TLS业务流，

否则后面的业务流添加不上

MA5620E(config)#service-port vlan 1002

{ eth }:eth

{ frameid/slotid/portid<1,15> }:0/1/4

{ other-all|user-encap|user-vlan }:user-vlan

{ untagged|user-vlanid<1,4094> }:untagged

{ rx-cttr }:rx-cttr 6 tx-cttr 6

//添加PC2的业务流

MA5620E(config)#service-port vlan 1002

{ eth }:eth

{ frameid/slotid/portid<1,15> }:0/1/5

{ other-all|user-encap|user-vlan }:user-vlan

{ untagged|user-vlanid<1,4094> }:untagged

{ rx-cttr }:rx-cttr 6 tx-cttr 6

//添加PC3的业务流

通过上面配置，PC2、PC3就可以开始拨号上网，或者配置静态IP地址进行上网。

4.5 配置针对MA5606T的业务数据

在MA5680T上配置对应的业务流:

MA5680T(config)#vlan 1001 smart

//配置业务VLAN=1002 to 1003

MA5680T(config)#port vlan 1001 0/20 0

//从上行口0/20/0透传业务VLAN

MA5680T(config)# service-port vlan 1001 epon 0/15/0 ont 2 multi-service user-vlan 1001

MA5606T的业务数据配置:

MA5606T(config)#vlan 1001 smart

//配置业务VLAN=100

MA5606T(config)#port vlan 1001 0/1 0

//从上行口0/1/0透传业务VLAN

MA5606T(config)# service-port vlan 1001 adsl 0/3/0 vpi 0 vci 35

multi-service

user-vlan untagged rx-cttr 6 tx-cttr 6

通过上面配置，PC1就可以开始拨号上网，或者配置静态IP地址进行上网。

EPON配置MA5680T的带内网管数据:

MA5680T(config)#vlan 100 smart

//配置带内网管VLAN=100

MA5680T(config)#port vlan 100 0/20 0

//从上行口0/20/0透传VLAN

MA5680T(config)#interface vlanif 100

//创建VLAN接口并进入VLAN接口配置模式

MA5680T(config-if-vlanif100)# ip address 192.168.100.1 255.255.255.0

//配置带内网管地址

MA5680T(config)#ip route-static 0.0.0.0 0.0.0.0 192.168.100.254

//配置缺省路由

EPON配置MDU的带内网管数据:

注:MA5620E可以在MA5680T实现远程配置，如果是近端通过串口登录，配置步骤参考MA5680T

的带内网管配置，只是上行口不一样，MA5620E上行口固定为0/0/1);MA5606T新开局不支

持远程配置，必须使用串口登录。

MA5680T(config)#service-port

{ index<0,16383>|vlan|desc }:vlan

{ vlanid<1,4093>|aoe }:100

{ adsl|shdsl|vdsl|atm|eth|gpon|epon }:epon

{ frameid/slotid/portid<1,15> }:0/15/0

{ ont }:ont

{ ontid<0,63> }:1

{ |multi-service }:multi-service

{ user-vlan }:user-vlan

{ user-vlanid<1,4094>|untagged }:100

Command:

service-port vlan 100 epon 0/15/0 ont 1 multi-service user-vlan 100

//配置针对MA5620E的带内网管的业务流

MA5680T(config)# service-port vlan 100 epon 0/15/0 ont 2 multi-service user-vlan 100

//配置针对MA5606T的带内网管的业务流

MA5680T(config)#interface epon 0/15

MA5680T(config-if-epon-0/15)#ont ipconfig //在单板模式下可以配置MA5620E的带内网

管数据

{ portid<0,3> }:0

{ ontid<0,63> }:1

{ ip-address }:ip-address

{ ip-address }:192.168.100.2

{ mask }:mask

{ mask }:255.255.255.0

{ gateway }:gateway

{ gateway }:192.168.100.254

{ manage-vlan }:manage-vlan

{ managevlan<1,4093> }:100

MA5680T(config-if-epon-0/15)#

The ONT IP is configured successfully

MA5680T(config-if-epon-0/15)#quit

MA5680T(config)#ping 192.168.100.2 //配置完成后，可以通过PING命令来检查

PING 192.168.100.2: 56 data bytes, press CTRL_C to break

Reply from 192.168.100.2: bytes=56 Sequence=0 ttl=63 time = 42 ms

Reply from 192.168.100.2: bytes=56 Sequence=1 ttl=63 time = 7 ms

Reply from 192.168.100.2: bytes=56 Sequence=2 ttl=63 time = 6 ms

Reply from 192.168.100.2: bytes=56 Sequence=3 ttl=63 time = 6 ms

Reply from 192.168.100.2: bytes=56 Sequence=4 ttl=63 time = 6 ms

MA5680T(config)#telnet 192.168.100.2 //如果能ping通，就可以telnet登录配置其它数

据

{ |service-port<0,4294967295> }:

Command:

telnet 192.168.100.2

Press CTRL_] to quit telnet mode

Trying 192.168.100.2 ...

Connected to 192.168.100.2 ...

>>User name:root

>>User password:mduadmin

Huawei Integrated Access Software.

Copyright(C) Huawei Technologies Co., Ltd. 1998-2008. All rights

reserved.

MA5620E>

MA5606T的网管数据配置，需要使用串口登录。

MA5606T(config)#vlan 100 smart

//配置带内网管VLAN=100

MA5606T(config)#port vlan 100 0/1 0

//从上行口0/1/1透传网管VLAN

MA5606T(config)#interface vlanif 100

//创建VLAN接口并进入VLAN接口配置模式

MA5606T(config-if-vlanif100)# ip address 192.168.100.3 255.255.255.0

//配置带内网管地址

MA5606T(config)#ip route-static 0.0.0.0 0.0.0.0 192.168.100.254

//配置缺省路由

MA5606T(config)#ping 192.168.100.1

PING 192.168.100.1: 56 data bytes, press CTRL_C to break

Reply from 192.168.100.1: bytes=56 Sequence=0 ttl=254 time = 12 ms

//检查网管是否配置成功

EPON配置能力集模板并确认:

//添加Profile-ID=30用来支持MA5620E

MA5680T(config)#ont-profile add epon profile-id 30

{ |profile-name }:

Command:

ont-profile add epon profile-id 30

Press 'Q' or 'q' to quit input

> Ont Manage Mode<1-SNMP, 2-SNMP-NOPARA, 3-OAM> [3]:1

> Is UNI configuration concerned?<1-not concern, 2-concern> [2]:1

Adding an ONT profile succeeded

Profile-ID : 30

Profile-Name : ont-profile_30

//添加Profile-ID=21用来支持MA5606T

MA5680T(config)#ont-profile add epon profile-id 21

{ |profile-name }:

Command:

ont-profile add epon profile-id 21

Press 'Q' or 'q' to quit input

> Ont Manage Mode<1-SNMP, 2-SNMP-NOPARA, 3-OAM> [3]: 3

//针对MA5606T的能力集模板只能选择3，不支持SNMP方式。

> Is UNI configuration concerned?<1-not concern, 2-concern> [2]:1

Adding an ONT profile succeeded

Profile-ID : 21

Profile-Name : ont-profile_21

MA5680T(config)# interface epon 0/15 //进入EPON单板配置模式

MA5680T(config-if-epon-0/15)# port 0 ont-auto-find enable //打开端口自动发现功能

MA5680T(config-if-epon-0/15)#

! EVENT WARNING 2008-04-11 18:06:41 ALARM NAME :ONU in Auto-find

state alarm

PARAMETERS :FrameID: 0, SlotID: 15, PortID: 0, MAC: 0018-8256-3E47,

Password: -

! EVENT WARNING 2008-04-18 10:33:18 ALARM NAME :ONU in Auto-find

state alarm

PARAMETERS :FrameID: 0, SlotID: 2, PortID: 0, MAC: 0018-822A-F4F3,

Password

: -

//ONU自动上报设备MAC

MA5680T(config-if-epon-0/15)# ont confirm

{ portid<0,3> }:0

{ ontid|all }:ontid

{ ontid<0,63> }:1

{ password-auth|mac-auth }:mac-auth

{ mac<14,14> }: 0018-8256-3E47

{ profile-id|profile-name }:profile-id

{ profile-id<1,128> }:30

{ |multicast-mode|multicast-fast-leave|description|fec|dba-profi

le|encrypt|cir }:

//使用profile-id=30确认MAC=0018-8256-3E47的MA5620E

MA5680T(config-if-epon-0/15)# ont confirm

{ portid<0,3> }:0

{ ontid|all }:ontid

{ ontid<0,63> }:2

{ password-auth|mac-auth }:mac-auth

{ mac<14,14> }: 0018-822A-F4F3

{ profile-id|profile-name }:profile-id

{ profile-id<1,128> }:21

{ |multicast-mode|multicast-fast-leave|description|fec|dba-profi

le|encrypt|cir }:

//使用profile-id=21确认MAC=0018-822A-F4F3的MA5606T

MA5680T(config-if-epon-0/15)#display ont info //查看ONT状态

{ portid<0,3>|remote }:0

{ ontid<0,63>|all }:all

Command:

display ont info 0 all

-----------------------------------------------------------------------------

F/S/P ONT-ID MAC Control Run Config Match Loopback

Flag State State State State

-----------------------------------------------------------------------------

0/15/0 1 0018-8256-3E47 active up normal match disable

0/15/0 2 0018-822A-F4F3 active up normal match disable

-----------------------------------------------------------------------------

In port 0, the total of ONTs are: 2

MA5680T(config-if-epon-0/15)#

5600加单板的方法:

1.确认单板 board confirm 0/1

2.去激活单板，并增加流量模板

进入单板状态:interface adsl 0/1

去激活单板:deactivate all(all指全部端口，也可指定单个端口)

激活单板:activate all profile-index 2 (all指全部端口，也可指定为单个端口，2

指profile-index模板，一般为2或4)

3. 增加vpi 和vci模板(在更改的时候还需要undo一下 undo service-port

vlan adsl 端

口)

可通过display curr 来查看其他单板或端口的配置方法(在列表的下半部分);形式如

下:

service-port vlan 305 adsl 0/9/25 vpi 0 vci 35 rx-cttr 8 tx-cttr 8

service-port vlan 305 adsl 0/9/26 vpi 0 vci 35 rx-cttr 8 tx-cttr 8

service-port vlan 305 adsl 0/9/27 vpi 0 vci 35 rx-cttr 8 tx-cttr 8

service-port vlan 305 adsl 0/9/28 vpi 0 vci 35 rx-cttr 8 tx-cttr 8

service-port vlan 305 adsl 0/9/29 vpi 0 vci 35 rx-cttr 8 tx-cttr 8

service-port vlan 305 adsl 0/9/30 vpi 0 vci 35 rx-cttr 8 tx-cttr 8

service-port vlan 305 adsl 0/9/31 vpi 0 vci 35 rx-cttr 8 tx-cttr 8

0/9/25为端口;8为模板(一般配置为7和8;但也有不同)。将上面的端口改为要更改的端

口，模板号改为要更改的模板号执行即可;

至此更改模板已经完成。