2024年7月24日发(作者：利惠美)
Menu
Used to manually save a minute value as the offset. It is added to or subtracted from
the current calibration value.
w
§
Select it to adjust the lighting for the Line Scan Camera.
§
Select it to adjust the lighting for the Down Camera.
w
§ Inner
Adjusts the inner lighting for the camera of the selected Gantry.
§ Middle
Adjusts the middle lighting for the camera of the selected Gantry. It is not used
for the Down Camera.
§ Outer
Adjusts the outer lighting for the camera of the selected Gantry.
16.4.10.1. Procedure
w Manual procedure
1. Move the Camera to a position where the head mark can be marked.
2. Mark the Head position by selecting Jog Z Mode and moving the Z axis.
3. Move the Camera again and find the center of the mark, then press the Enter
button on the Teaching Box.
4. Repeat above procedure for all the Heads.
w Automatic procedure
1. Put the tools in the calibration palette and put the double-faced adhesive tape on
the placement position.
2. Index the calibration palette as the work position.
3. Mount a nozzle that can pick up the calibration tool on the Head.
4. Press the Calibrate Button to start calibration.
5. Repeat above procedure for all the heads.
If this process is not calibrated properly, the head and the
conveyor might collide.
Caution
Do not execute calibration without an accurate Calibration
Tool.
16.5. TableTop Config. [F6]
Sets the configuration of Feeder Base, Auto Nozzle Changer, and standard Dump Box
16-27
Samsung Component Placer CP-60L Operations Manual
Figure 16-19. "Configure TableTop" dialog box
w
Displays the configuration status of Feeder Base, Nozzle Changer, and Dump Box in
the current machine.
w
box.
w
Displays all available devices that can be added to the TableTop
w
Displays the position on the Tabletop where the Device can be installed.
w
Select a device from the
install from the
appears in the
w
Saves the changes and ends the dialog box.
w
Disregards the changes and ends the dialog box.
16.6. Tray [F8]
Used to install the MatrixTray Holder on the Feeder base.
16-28
2024年7月24日发(作者：利惠美)
Menu
Used to manually save a minute value as the offset. It is added to or subtracted from
the current calibration value.
w
§
Select it to adjust the lighting for the Line Scan Camera.
§
Select it to adjust the lighting for the Down Camera.
w
§ Inner
Adjusts the inner lighting for the camera of the selected Gantry.
§ Middle
Adjusts the middle lighting for the camera of the selected Gantry. It is not used
for the Down Camera.
§ Outer
Adjusts the outer lighting for the camera of the selected Gantry.
16.4.10.1. Procedure
w Manual procedure
1. Move the Camera to a position where the head mark can be marked.
2. Mark the Head position by selecting Jog Z Mode and moving the Z axis.
3. Move the Camera again and find the center of the mark, then press the Enter
button on the Teaching Box.
4. Repeat above procedure for all the Heads.
w Automatic procedure
1. Put the tools in the calibration palette and put the double-faced adhesive tape on
the placement position.
2. Index the calibration palette as the work position.
3. Mount a nozzle that can pick up the calibration tool on the Head.
4. Press the Calibrate Button to start calibration.
5. Repeat above procedure for all the heads.
If this process is not calibrated properly, the head and the
conveyor might collide.
Caution
Do not execute calibration without an accurate Calibration
Tool.
16.5. TableTop Config. [F6]
Sets the configuration of Feeder Base, Auto Nozzle Changer, and standard Dump Box
16-27
Samsung Component Placer CP-60L Operations Manual
Figure 16-19. "Configure TableTop" dialog box
w
Displays the configuration status of Feeder Base, Nozzle Changer, and Dump Box in
the current machine.
w
box.
w
Displays all available devices that can be added to the TableTop
w
Displays the position on the Tabletop where the Device can be installed.
w
Select a device from the
install from the
appears in the
w
Saves the changes and ends the dialog box.
w
Disregards the changes and ends the dialog box.
16.6. Tray [F8]
Used to install the MatrixTray Holder on the Feeder base.
16-28